IS 277 BIS Certification for Galvanized Steel Sheets ( Plain and Corrugated)

About IS 277

Editions and amendments of IS 277

Amendments:First Amendment (2023), Second Amendment (2025), Third Amendment (2026). Test reports must reflect the standard with its amendments.

Marking fee for IS 277

BIS charges an annual minimum marking fee for the ISI mark under IS 277, set by unit size, plus a per-unit rate once production passes the minimum:

Unit rate: ₹4.5 per tonne. Source: BIS marking fee schedule for Scheme-I products, September 2026.

Sampling and key tests for IS 277

From the BIS product manual for IS 277 (Jan 2024), which BIS officers and applicants follow for certification:

Sample quantity:5 pieces of 5 cm X 5 cmor 50 g drillings

Raw material requirements:

• Included but not limited to IS 513 Pt.1 & 2(CR Sheet and Strip) and IS 1079(HR Sheet and Strip). Zinc Ingots used for galvanizing shall confirm to any of the grades specified in IS 209 or IS 13229.

Tests BIS can carry out in a day during factory inspection:

• All tests

The full type test covers every clause of IS 277; the list above is what can be checked on site.

ISI licences under IS 277

BIS records 55 operative licences (55 including deferred, cancelled or under stop marking). Most licensed factories are in Maharashtra (12), Uttar Pradesh (9), Gujarat (5), West Bengal (5), Odisha (5).

Testing against IS 277

BIS inspects the factory and has samples tested to the full Indian Standard at a BIS or BIS-recognised laboratory. After grant, the factory keeps testing production under the Scheme of Inspection and Testing, and BIS draws factory and market samples.

The test report has to cover every clause of IS 277 that applies to the product, in the edition current on the date of testing. When BIS revises IS 277 or replaces it with a new edition, existing licence holders move to the new edition by the date BIS sets in its notification.

How to get an ISI mark licence under IS 277

The licence is granted to the manufacturer for a specific factory and product. Indian factories apply under Scheme-I; overseas factories apply under the Foreign Manufacturers Certification Scheme (FMCS) and must nominate an Authorised Indian Representative.

1. Confirm the exact Indian Standard and the varieties to cover
2. Get the product tested at a BIS-recognised lab (simplified procedure) or arrange BIS sampling
3. Apply on Manak Online with factory, quality-control and test documents
4. BIS factory inspection and sample verification
5. Grant of licence, then marking with the ISI mark and CM/L number

Timeline. BIS targets 30 days under the simplified procedure (applying with a recent lab test report) and 90 days under the normal procedure. Overseas factories under FMCS typically take around 6 months.

Fees. Application fee ₹1,000 and annual licence fee ₹1,000, inspection charges of ₹7,000 per man-day, testing charges, and an annual minimum marking fee set for each Indian Standard (with concessions for micro and small units).

Mark. Certified products carry the ISI Standard Mark with the IS number and the CM/L-XXXXXXXXXX licence number.

Frequently asked questions

Other standards in Steel and Iron Products

• IS 280 Mild Steel Wire for General Engineering Purposes
• IS 412 Expanded Metal Steel Sheets for General Purposes
• IS 432 2 products
• IS 513 2 products
• IS 648 Cold Rolled Non-oriented Electrical Steel Sheets and Strip-fully Processed Type (CRNO)
• IS 963 Chrome Molybdenum Steel Bars and Rods for Aircraft Purposes
• IS 1029 Hot Rolled Steel Strip (bailing)
• IS 1079 Hot Rolled Carbon Steel Sheet, Plate and Strip —
• IS 1110 Ferrosilicon
• IS 1148 Steel Rivet Bars (medium and High Tensile) – for Structural Purposes

Source: BIS lists of products under compulsory certification (Scheme-I, Scheme-II), checked October 2026. See the full BIS product list or all Indian Standards.